Olson Network

AS400260 · Bemidji, Minnesota

Dial-Up Internet Access


Settings

Numbers
+1 218-210-5600 (PSTN)
696-1560 (PhreakNet)
696-5600 (PhreakNet)
Username
guest
Password
dialup
Protocol
PPP (async, 8-N-1)
Authentication
PAP
Serial
8 data bits, no parity, 1 stop bit, hardware flow control
Multilink
Supported (RFC 1990). Dial several lines with one login for one address and their combined speed. Setup
Modulation
V.92, V.90, V.34, V.32bis, V.22bis
IP address
Assigned by server
DNS
9.9.9.9

Two ways in

Both work on every number. Nothing needs to be selected in advance.

PPP client
Dial and let the client negotiate. Nothing to type.
Terminal
Dial with a terminal program. The server prompts for a username and password, then starts PPP.

Checking the line

Dial the number with any terminal program to confirm a login works before configuring a client. After CONNECT the server sends a banner and prompts:

Username: guest
Password:

Entering PPP mode.
Async interface address is unnumbered (Loopback0)
Your IP address is 0.0.0.0. MTU is 1500 bytes

The line then fills with unreadable characters. That is PPP, and it means the login succeeded. Hang up, or connect with a PPP client. The address shown is 0.0.0.0 because a pool address is assigned when PPP negotiates; an account with a reserved address sees that address here instead.

Windows 95, 98, Me

  1. Dial-Up Networking → Make New Connection. Enter the number.
  2. Properties → Server Types: PPP. Uncheck Log on to network, NetBEUI and IPX/SPX.
  3. TCP/IP Settings: server-assigned address; name server 9.9.9.9.

Windows 2000, XP

  1. New Connection Wizard → Connect to the Internet → Set up manually → Dial-up modem.
  2. Properties → Security → Advanced: allow Unencrypted password (PAP) only.

Mac OS 7.5–9

  1. Modem: select your modem and port.
  2. TCP/IP: connect via PPP, configure using PPP server, enter the name server.
  3. Remote Access: enter the login and number. A command-line host with Connect to a command-line host also works if you prefer to log in by hand.

Linux / BSD

[Dialer Defaults]
Modem = /dev/ttyS0
Baud = 115200
Init1 = ATZ
Phone = +1 218-210-5600
Username = guest
Password = dialup
Stupid Mode = 1

wvdial shown. For pppd, use refuse-chap refuse-mschap refuse-mschap-v2. No login chat is needed after CONNECT; a chat script that answers sername: and assword: also works.

Multilink PPP (RFC 1990) joins calls on several modems and phone lines into one connection. Each modem dials with the same login, and the server bundles the calls: one IP address, with the lines’ speeds combined and traffic spread across them. Each line is a separate call and occupies a modem here, so a bundle uses as many modems as it has links; eight-link bundles have been tested. Any account can multilink, including guest. While a bundle is up, the status page shows its throughput, and the call history lists it as one entry with its links beneath.

Windows 98
Connection Properties → Multilink → Use additional devices → Add the second modem and its number.
Windows 2000, XP
Connection Properties → General: check both modems. Options → Multiple devices: Dial all devices.
Linux / BSD
Add multilink to the pppd options and start one pppd per modem with the same login. Each later link joins the first link’s ppp0 and logs Link attached to ppp0.

Troubleshooting

Busy
All modems in use. Check status.
No carrier
Force a lower standard: AT+MS=V34 (33.6k) or AT+MS=V32B (14.4k). US Robotics: AT&N.
Drops at login
Use PAP. CHAP and MS-CHAP are refused.
Unreadable characters
PPP has started. Expected: connect with a PPP client rather than a terminal.
Login fails
Member accounts use the user number and PIN from self-service.